Monday, March 6, 2017

Cabin Doors & Transparencies - Part 1


Section 45
If you've done it yourself or have followed anyone's build you'll know that the doors are a dreaded step in the build.  I'm about 50 some odd hours into section 45 and probably have a good 50-100 hours to go till completion.  Need a bit of attention to detail to work through the section and should ask questions if you have any. Mess ups not might not come around till later and then you will end up having to back track.

I'm moving a bit out of order in this section.  For example where I'm sitting right now is preparing to glass in the windshield.  Per the plans this is typically done post door finalization, however waiting on some after market parts to do the door functioning mechanisms. It's a non issue but wanted to throw that out before I continue through this. Also will probably be more pictures than writing, you spend a lot of time on small parts of the plans.

Cabin Doors

This jist of the doors is you take the parts Vans sends you, rough cut and line up to a series of index holes.  Not my index holes were a bit off so as long as you can get the front and the back to line up it all works out.  After initial trimming and test fitting I added some insulation and then glued them together.


Free Child Labor



Free Adult Labor




Ready for some brackets and then glue
More kid labor



Insulation before glue, didn't install where door mechanism will go.

Parabeam material from Vans.  Interesting stuff


My middle kid was a huge help on gluing the door halves together.  She walked into the garage at the wrong time and I quickly recruited her.  I used a mess of tape to hold these things in place, checking and triple checking.  At this point if they are way off then you're pretty much going to start over with a new set.





 After epoxy cures you can then remove and trim up.  After I could get them to set in the door cabin recess I made new brackets to hold them in place aligned with the index tabs.  These were used to align and get the door hinges together.





Typical to using the McMaster door seal is the modification of closing off the door hinge gap as well as using nutplates.  Here are pictures of that activity.










Transparencies

In between some things I got working on the transparencies, this includes the windscreen fit, rear and door windows. I also painted the glare shield which I plan to cover at some point also.  I went ahead and touched up the center brace since it got scratched fitting the wind screen.  I used Lord Adhesive to attach all transparencies and am now in the process of taping out and finishing up the outside of these to make them look good.  Also have prepped the windscreen area for all the layups and filler on that.

Final Fit Windshield









Current State, oh I put the engine mount on too...
The above picture shows the planes current progress.  I have a lot to do and just for reference here's a quick checklist to finish this section.
  • Install Aerosport door handle and PlaneAround latch system.
  • Get final 3/16th or so reveal around door.
  • Do windscreen transition and layups
  • Sand, fill, sand, fill, sand.... the area's around the transparencies and any areas I want to look better
  • Finish and paint inside of door.
Hey only 5 things but like I said in the beginning certain tasks such as the sand, fill repetitive process will take weeks if not months!

Sunday, February 19, 2017

Empennage Revisit

About a year ago I called my Empennage finished.  I mentioned that it's more of a 'done for now' type thing than being finished.  I decided to wait to do this aft piece to make it easier to mess within the tailcone while I tried to figure out what all happens back there. There were several things I wanted to work through at a later day before I went ahead and riveted on the aft tailcone skin.  Could of done this a year ago but really didn't know, wanted to limit my time climbing into the tailcone.

I'm actively working through the doors which involve some fiberglass work leaving gaps of time to work on other things.  One of these things was to finish up the riveting of the aft top tailcone skin.  Since I have a good idea of what's going to go back there I decided to at least get cable tie bases secured. I also used some caterpillar edging around the lightening holes where I will end up with cabling pushed through. Below is a picture showing the cable tie bases secured to the side.  I ended up mirroring both sides to give me options later on when running cabling.  These are just 3/4" bases where I used acetone to remove the factory adhesive and I used some super strong 3M 2 part epoxy type stuff to glue it to the sides.  Surface prep is always important so when you figure out where you want to put these you can just sand a bit off.  To test I pulled on these fairly hard to a point that if I kept pulling would end up just puckering the skin.


Secured cable tie bases 
With that out of the way I riveted up the aft skin.  A majority of it I did solo but found it much easier and had better results with a second set of hands.  My neighbor came down and helped buck these rivets (He ended up having to crawl into the tailcone).  This was one of the few times that I've riveted with two people and to be honest you get a much more consistent result when you can focus on holding the rivet gun in place.  Looking back it would of been nice to do the entire plane with two people. After that we cleaned it up a bit and cleco'd back on the center section.  I will wait till much later to rivet this piece on.  Probably during final assembly.

Aft skin riveted in place.

Wednesday, February 1, 2017

Finishing Kit Delivery

It took about two and a half months but this morning my finishing kit was finally delivered.  To be fair the original date was early January but I traveled for work two last month for extended period so had them put a delay on shipping until I knew I was going to be here for a week.  Surprisingly the box was a lot smaller than I anticipated.  There was a small puncture in the box so cracked it open while the driver was still here to make sure nothing was damaged.  All is good.

Finishing Kit
With my neighbors assistance we were able to inventory the kits fairly expeditiously. After a few hours everything was accounted for and in place for future attachment to the plane.  The pictures are a bit misleading as everything still takes up quite a bit of space, but there are a lot of larger pieces.



Tuesday, January 17, 2017

Avionics Fans

This plane will end up with a lot of equipment both on the panel and sitting behind the panel.  This leads to heat generation which isn't the best thing for electronic components.  The RV-14 kit actually has you install two fans on the glare shield and many builders of the RV-10 have taken it upon themselves to add a few fans of their own.  I decided to join in on the fun, and at the same time log a little build time.

The idea is fairly simple, mount two fans under the glare shield to push the hot air out and replace with cooler air under the foot well. An added effect to these is they will also function as defrosters on the windshield.  At first the idea of flying at any time when I have ice on my windshield seems a bit nutty but my neighbor who is a military pilot said it has more to do with condensation. As a result some people have wired these fans to a switch labeled 'defrost' and manually turn it on and off.  I'm not going to do that but rather have them wired in a way that they remain on anytime I have the master on.  The added benefit is when you shut down the plane you'll know your master is left on if you hear the fans.

In regards to fan selection most any computer style cooling fan will probably work.  The common size seems to be 80mm or around 3" fans although I've seen larger ones and smaller ones used by builders.  I went with 80mm and probably spent way too much time selecting the ones I wanted.  In my typical overthinking method I wanted ones that were relatively thin as to not impose onto the forth coming avionics install, while still moving a lot of air and keeping someone quite (Which is silly given the engine is 2 feet away). I selected the OD8025-12HB from Digi-Key with an associated cover (10020-1-5170). These fans seemed to offer a good balance of air throughput and sound.

Something to note on the installation is there is very very little margin of error in lining up the fan hole with the guard attachment holes. On some of the side about a 1/16 of an inch hang out under the grill screen.  I'm not particularly concerned with that because I will be covering the glareshield with some type of material which will require me to work it around the holes so it will end up getting recovered.  However if you don't plan on doing something like that and that detail will bug you then maybe do the hole a bit smaller than the fan size.


Holes Drilled
Installed Top
Installed Bottom

Friday, January 13, 2017

New Year, N Number and Panel/Electrical Designs

N Number

Last year I reserved N405JW but I wasn't really sold on it.  Over the last year I've been waiting for something that I liked better.  A fantastic resource to use is an aggregation site at http://www.tailnum.com/. This makes the registry searchable as well allows you to see newly released numbers available.  Hey and it also happens to be maintained by a fellow RV builder. While it's very possible I might change it again, at this point I registered an am going with N910W. Easy to remember and fairly self explanatory being a combination of the build and my last name.

Panel Design

Haven't made a lot of physical progress in the build over the last month.  I'm awaiting the finishing kit and decided to use the time to jump into finishing up a few planning items. Not only did this require putting some things down on paper but an extensive amount of reading! In the end I think I ending up reading 5 books and countless posts, logs and other bits of information. The last book I read on the subject really should of been my first book and is Marc Ausman's Aircraft Wiring Guide.  Marc was the original designer of the Vertical Power system that I'll be using.  The book is short (80 pages), concise and is a great intro into the subject.  It has a bit of marketing material on the VPX but since I'm already sold on it I wasn't bothered.

Digging into panel design is so far my favorite part of the build.  I actually started looking into this before I even ordered the first kit.  The ability to customize essentially everything that goes into it is a huge draw and really shifted me from the certified market over to the experimental.  The path of progression started by looking at other panels, learning about the various components and trying to determine a starting point of what fits your flying mission.

I started drawing out designs on a piece of paper and soon moved to using MS Paint in sort of a Frankenstein panel creation method.  This got me through a good 10 or so revisions.  Recently I transferred that over to a Visio drawing which is a lot easier to modify and maintain.  Pending any major changes in product lines this is very close to what I will go with.

Panel Design

The quick rundown is I wanted a solid single pilot IFR capable platform.  I want to have full access to everything with a good bit of visibility for night flights where I don't have to wear a headlamp or install a ton of lights.  I'm obviously a Garmin fan because essentially the entire panel is made up of their product line.  What you can't see on the panel are the remote comm #2, transponder and ADSB stuff which will be remotely controlled through the other devices.

Each rocker switch will be customized illuminated switches and everything flows in a particular phase of flight process.  Ie Left side are the starting functions, first set of buttons are the most used ones, the lights are together and the A/C Climate stuff is together.  I may move the ELT things (Top left) around but not sure.

I'm putting a lot of functionality on the control sticks themselves. I will essentially be able to fly 'hands on' during the critical phases of flight (Take off & Landing).  Not shown is the throttle, props and mixture which will be on the center console.

Electrical System

Think about building a car, then think about trying to figure out how all the wiring is connected between everything and you'll have a good idea of what goes into building a plane. You can buy a harness and use some plans from Vans but you'll end up with a very plane Jane set up.

Not interested in that approach I've spent the last few months off and on either reading about electrical systems or working on a set of drawings to the design.  I'm off the hook on somethings like the interconnecting harnesses between the avionics.  I'm going to get those through Stein Air on a majority of the devices which saves time, but really saves headache and heartache of trying to complete that on my first project.

What I first focused on was the component layout of the plane to determine where physically everything will be located.  This also forces you to think about everything and even in this basic exercise I added and removed things multiple times.  The endish result looks like this-

Component Overview
Once you have a panel design figured out and where you want to put the components you start to dig into how power is going to be distributed.  This has quite a steep learning curve as it requires you to read about the requirements of your planned components, look at other peoples designs and make some decisions.  




What a mess right?  I promise it makes sense... or at least I hope it does.  It really gives you a great idea of the various wires and connections you'll need to make to get power throughout the plane. It again forces you to really understand what you're putting in the plane even down to the wire size.  I probably made at least 10 major revisions on the above and as it stands now will probably be tweaked continually throughout the life of the plane.

I found out that electrical systems are HIGHLY debatable.  There's no one right way to do it and what is within the comfort level of some people is not for others.  The basis of my design is to allow several backup options if I lose ship power in IMC (Clouds).  If I can see out the plane window I'm less concerned about being able to fly and land safely but in the clouds losing something like attitude indication can be a real problem.

What I'm going with is a single main battery with dual alternators. I'll also utilize a smaller backup battery for the main EFIS, GPS and a few other items.  The last resort is the Garmin G5 which also has it's own backup battery.  Again my goal if I have a problem isn't to continue the flight through IMC until I run out of gas, it's to get out of the clouds and land.  If your mission is otherwise then you can really build it as redundant as you want.

These are just a few of the drawings I wanted to share.  I would suggest in building your project you put together a 'book' of drawings in whatever format you want.  So far I have a total of 7 separate drawings that cover in details some of the specific items in the plane.  Will be invaluable in future troubleshooting or modification en-devours. 

Friday, December 16, 2016

Cabin Cover Part 2


I started my work with the Cabin top back in July, so about 6 months ago.  Wasn't consistent work and you can read about the initial fitting here.  Since then I've been going back and forth doing little things here and there with it.  I originally thought securing the cabin top was something you finalize and accomplish later. Some people put it off longer than others but decided to follow the plans and throw it on now. Seems once you have the basic fuselage done you can start on the canopy, just don't do the windows and doors until permanently attached and your doors are hung. I had a lot of confusion but the good folks at VAF straightened me out and suggested the order of things-
  • Install the big conduits that run under the rear seats and baggage compartment floor. 
  • If using remote ADHARS modules make the shelf for them now. 
  • When done with the canopy, paint the plane interior.
  • Paint the inside top of the canopy. 
  • Mount the rudder pedals, run the brake and fuel lines, and do all the wire runs you can leaving the ends long for final wire. Panel, avionics and all that other stuff waits until the end.
  • Now, permanently attached the canopy top and move on to glass and doors.
Conduit has been run, my ADHARS will mount in the front behind the panel and I painted the plane interior parts that will be visible post interior install.  That's not completely true, I did follow up later and painted some additional area's inside once the cabin top was mounted... but that's post attachment work.

Preparing and painting the cabin top is a lot harder and time consuming than I had originally anticipated.  A lot of my awkwardness is just the learning curve of working with fiberglass, having very little previous experience outside of the empennage parts. I previous learned a good bit doing that but learned so much more while working on the cabin top.  I wouldn't call myself adept at this point but I'm at least an experienced novice.  Your comfort level will increase the more hands on time you spend doing it.  

You have a lot of choices on this part as well.  If you're really concerned with time and don't care how it looks you can just clean it up a bit, maybe put some paint on it and get to installing it.  Your plane would have a top but it wouldn't be very nice inside.  What I went with was the Aerosport overhead console and I plan on using their headliner kit.  So I didn't have to be overly concerned with the back area of the cabin top but I did want a nice finish on the front visible area and that was were the time sink came in. Most my time was spent on a cycle of sanding, filling, priming and painting aiming for a particular finished look.

First part that I tackled was attaching the Overhead Console.  This is a very light and sturdy piece that comes with very little directions.  It's up to you to sort of work the installation through and figure out how you want it all installed.  You'll need to source and install things like nut plates and lights, decide if you want to paint it or keep it carbon fiber, ect.  For me I'm keeping it carbon fiber so I had to place it while at the same time trying not to mess up the flange pieces. 


Glassed in the Gap

Used some primer to see what I was sanding (Don't really need to do this)
Now before I get into the pictures of later steps I want to say up front that my level of efficiency with working on fiberglass is horrible. I'm sure I wasted plenty of epoxy, filler, paint, sandpaper ect in this little adventure but I'll chalk that up to the cost of learning.  There were several times I felt I was done, until I shot some primer over it and realized how just bad it looked.  What helped me the most outside of just doing it was watching a ton of videos (The late Mike Arnold's videos can be found here). I also spent countless hours reading other build logs and even talked to a car guy about body work.  Posting on the  forum always help and I did that with some questions on primer here.  Some tips and guidelines I picked up along the way are-
  • Do all shaping with low grit 60-120 sandpaper
  • If you need to add filler use epoxy resin and Microballons, thick enough to be applied in a single layer if possible.
  • Again sand with 60-120 until you are happy and don't see any low or high spots.
  • Skim coat with resin and sand off with some 320 or higher just to get it smoothed out.
Now the above is reiterative and I went through that process at least twice before I decided to do some heavy sanding removing some previous work and essentially starting back over.  That in itself took me three hours using a mess of 60 grit sandpaper, scotch brite and some acetone (Had to remove old primer).  Then I built up from there to get to where I could paint the product.  Some of what I did was completely unnecessary, for example hand contouring micro filler in certain areas.  That's really a challenge to get it looking symmetrical unless you're good with sculpturing which I'm not.  

I also had no real idea on how to use high build primer contributing to the 4 cans I wasted.  I went with aerosol for the ease and picked SEM products because I've had good luck with their paints.  I learned the painting process goes a bit like this.
  • Are you happy with the contour and quality of the part you're about to paint?  If not go back to the steps above because no amount of paint is going to magically fill in any flaws.
  • Spray a coat of dark colored primer, in my case I used cheap Rustoluem stuff that I have been using on the metal parts.  Then while still wet spray on a few coats of your high build.  The idea is when you start block sanding you'll see the dark color and know how close you are to the raw fiberglass.
  • Once cured block sand with 400 just to find any high or low spots.  Now some parts on the cabin top inside you can't really block.  But do your best to make sure there's no high or low spots and everything is still contoured how you like it.  If you hand sand use very little pressure to not make dips.  Now on mine there were some low spots that I didn't feel justified resanding and starting over so I just mixed a little filler and used that.
  • Top coat and once that's cured do a few coats of clear... I sanded with 1000 in between those.
Now the above sounds easy but it's far from that.  You really have to take your time and have some patience, I think my earlier issues were from a lack of knowledge and patience both.  I really kept thinking later steps like high build primer were going to fix my low spots and imperfections and it didn't.  But as with all parts of this project you have to work through it and rework if you need to and get it done correctly.

As I said it took me about three times to get it to a place I was happy with it. Here is a picture of my first attempt, it was obvious after I sprayed with Primer that I had not done this correctly.
First go at it... gross
The second time around I sanded off some of the primer and tried to 'patch' some of the spots.  Again went ahead with spraying on the primer and again wasn't happy with the results.

Better but still junk
The third go around I decided to take advice from the forum and this is where I spent the 3 hours removing all the previous layers. With the cabin top cleaned up I was ready to start again and over the course of a week or so put time into sanding, filling, sanding and filling to get the shaping completed while limiting highs and low spots.  After skim coating I found more areas I wasn't happy with and fixed those and reskim coated. To prime I used some Rustoluem dark primer put a coat of that on and immediately sprayed the high build primer over that.  This gives a bit of a guide on subsequent sanding where if I break through to the dark gray I know to stop.  If I have to sand below that then I'll have to reseal before restarting the priming in that area.  I did this a number of times which again slowed down the process.
Third time much better


After I removed the masked off area's I wasn't happy with my lines between the top and the carbon fiber piece.  I went ahead and sanded out the area with some 60, then 120 to recreate the lines.  Taped it back off and sprayed again.  Now there were actually some other area's I didn't like so I just worked those, cleaning them off and going through all the same steps I mentioned above.  I also resanded the carbon fiber with some 320 to get any paint overspray off.

Then started the cycle of redoing small spots all over the place. I actually may have been a bit too picky and even though I could see the vast improvement, there were still a few imperfections that I wanted to correct. In reality they weren't overly noticeable but nonetheless it was bothering me.  I spent a good amount of extra time doing patch fixes all over the place.  Then it occurred to me that I'm not building a show plane, there will be imperfections and I need not obsess over it. I decided that if I couldn't see the issue from a few feet away then I would move on.  Given all the work put into it I think it turned out well.

Final

Something I didn't really cover was the door seal which I worked on concurrently with all the other stuff.  I decided to go with a McMaster Carr product that attaches to the door opening vs per plans which puts a seal on the door.  For me a cleaner look on the edge and I had seen a number of builds which used these. Had to do some research to really figure out what was needed and how to do it.  In short depending on the seal you order you have to cut and sand the opening to accomodate this connecting on the inside.  Best resource I found to explain it can be found here, here is a picture of my end result, really won't know how well it works until I get the doors hung.

Door Seal
Finally past the cosmetic details of the inside of the cabin top it was time to move on with the plans. Fairly straight forward it consisted of some dimpling the skins, countersinking and match drilling some parts.  This was all per the plans and while a bit awkward at times to work with it was a fresh breath from my sanding/filing/priming/painting saga.  I was surprised that CS4-4 pull rivets were used to secure the cabin piece to the skins.  I'm guessing that Vans didn't want bucked or squeezed rivets damaging the fiber glass.  With that in mind I used the manual pull rivet tool vs the pneumatic.

There are some things you need to think about if you plan on putting any wiring in the overhead console.  I am putting lights and what not up there and will probably need a pair or two of 20-22 gauge wire.  Decided to route that down the front and through the cabin top brace.  To prepare I used rubber and plastic grommets along with some expandable sleeve material to act as a conduit.  It's hard to see in the picture below but the black sleeve material comes out the overhead and down the brace.


With the cabin top riveted to the side skins it was time to get some flox put on per the plans and tighten up all the hardware.  I'm not 100% sure if you're supposed to torque these to spec.  I'm guessing you're not since the attaching is being assisted with the flox. The process went really well although a bit messy.  When I tightened everything down I was happy to see the flox squeeze through meaning there shouldn't be any air gaps anywhere.  After that I cleaned up the fillet on the inside to leave it symmetrical all the way down.  Here's an early picture of wet flox.


Once this cured the shaping was essentially there so I just used 320 to smooth it out some more and to clean up any stray flox material.  Then as I did on the rest of the top I put some micro on to even it out some more, sanded and then skim coated followed by application of a few coats of high build primer.  My goal here was to paint any of the visible areas post interior install so sprayed more than the cabin top work I had done.  This included under the glare shield but used a graphite top coat vs warm gray.  This was all followed by some light sanding clear. My fiberglass skills have gone up at least one level or so during this process and the end result was solid.


This section also lays out the initial fitting of both the windshield and the rear windows. These don't get permanently attached until the doors are installed so I decided to go ahead and trim the rear windows but not mess with the windshield until the doors are on.  My logic is if I mess up on the rear windows they're easily replaced, while the windshield is a bit more challenging.

Installing the rear windows just took some time and patience.  You cut to the lines drawn on by Vans and then slowly remove more material until it sits nicely in the cabin top recesses.  It went fairly smooth but probably placed them on and off the plane a good 10 times each.  Take your time so you don't remove too much material.  I believe these lines get glassed in later on so it doesn't have to be perfect, but at the same time shouldn't be overly gouged up.

Untrimmed and just set on
Right side fitting
With all the fun stuff completed and the top now permanently attach section 43 is essentially wrapped up.  Because Section 44 is the wing attachment I'm done with the Fuselage for now until final assembly.  I say done but there are several side projects that I'm going to work on while waiting on the finishing kit to arrive. Should also note that I'm going to hold off on the forward tail skin until I'm finishing up the avionics. I don't want to have to crawl through the tailcone until it's necessary and leaving it open makes some prewiring and air conditioning items easier to work through.

Painted exposed area including under the glare shield

Put the windows and windshield up for safe keeping